GigaCore LED reference
Luminex GigaCore LED Reference
System Status LEDs
OK /
General Status LED
|
Icon |
State |
Description |
|
|
Solid Green |
System operating normally |
|
|
Blinking Green |
Writing to flash memory, do not power off |
|
|
Solid Orange |
Temperature warning |
|
|
Blinking Red |
Temperature or fan error |
|
|
Alternating Red/Green |
Firmware update in progress, do not power off |
Power LED
|
Icon |
State |
Description |
|
|
Solid Green |
Main PSU OK + redundant PSU connected |
|
|
Solid Orange |
Main PSU OK, no redundant PSU connected |
|
|
Blinking Red |
Power supply fault |
PoE System LED
|
Icon |
State |
Description |
|
|
Off |
No PoE available |
|
|
Solid Green |
PoE system OK + redundant PSU connected |
|
|
Solid Orange |
PoE system OK without redundant PSU |
|
|
Blinking Red |
PoE subsystem or power fault |
RLinkX LED
|
Icon |
State |
Description |
|
|
Solid Green |
RLinkX redundancy active |
|
|
Solid Orange |
At least one port on this switch is in the 'partial redundant' state |
|
|
Off |
No ports on this switch have RLinkX enabled |
Port LEDs
Link / Speed
LED
|
Icon |
State |
Description |
|
|
Off |
No link detected |
|
|
Solid Green |
1 Gbps Ethernet link |
|
|
Blinking Green |
1 Gbps Ethernet traffic/activity |
|
|
Solid Orange |
10/100 Mbps Ethernet link |
|
|
Blinking Orange |
10/100 Mbps Ethernet traffic/activity |
Group / VLAN
Mode
|
Icon |
State |
Description |
|
|
Group/VLAN Colour |
Port assigned to a specific VLAN/group |
RLinkX Port
Mode
|
Icon |
State |
Description |
|
|
Solid Blue |
Port configured as RLinkX redundant port (Gen1 GigaCores) |
|
|
Solid Blue |
RlinkX enabled and fully redundant connection (Gen 2 Gigacores) |
|
|
Solid Blue |
RlinkX enabled, no redundant connection (Gen 2 Gigacores) |
|
|
|
|
MultiLinkX
Mode
|
Icon |
State |
Description |
|
|
Solid Magenta |
MultiLinkX configured/enabled |
|
|
Solid White |
MultiLinkX active |
PoE Port Mode
|
Icon |
State |
Description |
|
|
Solid Yellow |
PoE enabled on port |
|
|
Solid Orange |
Port actively supplying PoE power |
|
|
Solid Red |
PoE fault/error |
Milan Mode
LEDs
|
Icon |
State |
Description |
|
|
Solid Pink |
Milan Primary network |
|
|
Solid Cyan |
Milan Secondary network |
|
|
Solid Purple |
Milan Auto mode |
|
|
Blinking Red + Pink |
Primary/Secondary mismatch |
|
|
Blinking Red + Cyan |
Secondary/Primary mismatch |
|
|
Off |
Milan disabled or trunk port |
Quick Troubleshooting Guide
|
LED Behaviour |
Interpretation |
|
Green blinking on OK LED |
Flash write in progress |
|
Red blinking on OK LED |
Fan or temperature fault |
|
Alternating red/green |
Firmware update active |
|
Green blinking on port |
Active gigabit traffic |
|
Orange blinking on port |
Active 100 Mbps traffic |
|
Blue solid on port |
RLinkX redundancy enabled |
|
Magenta solid |
Link aggregation configured |
|
White solid |
Link aggregation active |
|
Red on PoE port |
PoE fault or overload |
|
Pink or cyan Milan LEDs |
Milan network role indication |
Related Articles
GigaCore Gen2 API documentation
In the attached document you can find all the web API commands available for the second generation GigaCore. The API is also available on the device itself by browsing to http://{YOUR_DEVICE_IP}/api/doc This API works for Gen2 GigaCore switches. All ...LumiNode LED reference
Luminex LumiNode LED Reference DMX Port LED States LED State Description Solid Green DMX input idle Blinking Green Active DMX input detected Solid Cyan DMX output mode (DMX only), idle Blinking Cyan DMX output activity Solid Blue DMX + RDM output ...Can I transport the output data of my LED controller through the GigaCore Ethernet switch?
LED controllers such as Novastar or equivalent, use a non Ethernet based protocol to transport their pixel control protocol to the LED panels. It is therefore impossible to transport this kind of protocol through any Ethernet switch, including the ...LumiNode LED indicators
There are various LEDs on the LumiNode. Here is a list of the LEDs, the possible colours, and the meaning of each colour: DMX Port Status Meaning DMX Input Green Blinking: Active input DMX only (output mode) Cyan Blinking: DMX activity DMX + RDM ...Gigacore Switches and Avid S6L
As most of you probably know by now, Gigacore switches can be used to connect the different units in an Avid S6L system. The procedure to configure Gigacore switches is described by Avid in this document : ...